How to Restring Your Hyper Tough Weed Eater (Step-by-Step Guide) (2024)

Your Hyper Tough weed eater is a powerful tool that can help you keep your yard looking its best. But if the string breaks, it can be a pain to get it back up and running. Luckily, restringing a Hyper Tough weed eater is a relatively simple process. In this article, we’ll walk you through the steps, so you can get back to trimming your grass in no time.

We’ll start by discussing the tools and materials you’ll need. Then, we’ll show you how to remove the old string and install the new string. Finally, we’ll give you some tips for keeping your weed eater in good working order.

So, if your Hyper Tough weed eater is out of commission, don’t despair. Just follow these steps, and you’ll be back to mowing your lawn in no time.

Check Hyper Tough Weed Eater String on Amazon!

How To Restring Hyper Tough Weed Eater?

A Hyper Tough weed eater is a powerful tool that can be used to quickly and easily remove weeds from your yard. However, if the string on your weed eater breaks, it can be difficult to know how to replace it. This guide will walk you through the steps of restringing a Hyper Tough weed eater, so that you can get back to keeping your yard looking its best.

Tools and Materials

To restring a Hyper Tough weed eater, you will need the following tools and materials:

• Replacement string
• Pliers
• Tape measure
• Wire cutters

Step-by-Step Instructions

1. Turn off the weed eater and disconnect the spark plug wire. This will prevent the weed eater from starting accidentally while you are working on it.
2. Remove the old string. To do this, you will need to unscrew the two screws that hold the string guide in place. Once the screws are removed, you can lift up the string guide and remove the old string.
3. Measure the new string. The new string should be the same length as the old string. To measure the old string, simply lay it flat and measure it from end to end.
4. Cut the new string. Once you have measured the new string, you can cut it to the correct length.
5. Thread the new string through the weed eater. To do this, you will need to start by threading the string through the hole in the spool. Once the string is threaded through the hole, you can feed it through the eyelets on the weed eater’s head.
6. Tighten the string. Once the string is threaded through the weed eater, you can tighten it by turning the spool clockwise. Be careful not to tighten the string too much, as this could damage the weed eater.
7. Reattach the spark plug wire. Once the string is tightened, you can reattach the spark plug wire.
8. Test the weed eater. Now that the weed eater is restrung, you can test it to make sure that it is working properly. To do this, simply turn on the weed eater and let it run for a few seconds. The weed eater should be able to cut through weeds without any problems.

Restringing a Hyper Tough weed eater is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can get your weed eater back up and running in no time.

Here are some additional tips for restringing a Hyper Tough weed eater:

• Make sure to use the correct type of string for your weed eater. The string should be made of nylon or polyethylene and should be the same thickness as the old string.
• When threading the string through the weed eater, be careful not to kink or twist the string. This could damage the string and make it difficult to feed through the weed eater.
• Tighten the string until it is snug, but not too tight. If the string is too tight, it could damage the weed eater.
• Test the weed eater to make sure that it is working properly. The weed eater should be able to cut through weeds without any problems.

How To Restring Hyper Tough Weed Eater?

Restringing a Hyper Tough weed eater is a relatively simple task that can be completed in just a few minutes. However, it is important to follow the steps carefully to ensure that the weed eater is properly restrung and that you do not damage the machine.

Here are the steps on how to restring a Hyper Tough weed eater:

1. Gather your materials. You will need the following materials to restring your Hyper Tough weed eater:

• A new string spool
• A pair of pliers
• A screwdriver

2. Turn off the weed eater and disconnect the spark plug wire. This will prevent the weed eater from starting accidentally while you are restringing it.

3. Remove the old string. To remove the old string, you will need to first remove the spool cover. The spool cover is located on the top of the weed eater, and it is held in place by two screws. Use the screwdriver to remove the screws and then lift off the spool cover.

Once the spool cover is removed, you will see the old string wrapped around the spool. Use the pliers to grasp the end of the old string and pull it off of the spool. Be careful not to damage the spool or the string.

4. Align the new string with the old string. The new string should be aligned with the old string so that it is in the same position on the spool. This will help to ensure that the weed eater is properly restrung.

5. Thread the new string through the weed eater. To thread the new string through the weed eater, you will need to first thread it through the hole in the spool cover. Then, you will need to thread it through the hole in the weed eater’s housing. Finally, you will need to thread it through the hole in the weed eater’s head.

6. Tighten the string. Once the new string is threaded through the weed eater, you will need to tighten it. To do this, you will need to use the pliers to grasp the end of the string and pull it tight. Be careful not to overtighten the string, as this could damage the weed eater.

7. Reattach the spool cover. Once the string is tightened, you can reattach the spool cover. To do this, simply line up the holes in the spool cover with the screws on the weed eater and then screw the screws back in place.

8. Reconnect the spark plug wire. Finally, you will need to reconnect the spark plug wire. To do this, simply plug the wire back into the spark plug.

Now that your weed eater is restrung, you can test it out to make sure that it is working properly. Simply turn on the weed eater and let it run for a few minutes. If the weed eater is working properly, the string should be spinning evenly and the weed eater should be able to cut through weeds easily.

Restringing a Hyper Tough weed eater is a relatively simple task that can be completed in just a few minutes. By following the steps in this guide, you can ensure that your weed eater is properly restrung and that you do not damage the machine.

If you have any questions about how to restring a Hyper Tough weed eater, please consult your owner’s manual or contact the manufacturer.

How To Restring Hyper Tough Weed Eater?

Q: What tools do I need to restring my Hyper Tough Weed Eater?

A: You will need the following tools:

• A Phillips head screwdriver
• A pair of pliers
• A new string trimmer line

Q: How do I remove the old string from my Hyper Tough Weed Eater?

A: To remove the old string, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string trimmer head.
3. Use the Phillips head screwdriver to remove the screws that hold the string trimmer head in place.
4. Remove the string trimmer head.
5. Use the pliers to remove the old string from the string trimmer head.

Q: How do I install the new string on my Hyper Tough Weed Eater?

A: To install the new string, follow these steps:

1. Thread the new string through the eyelets on the string trimmer head.
2. Make sure that the string is the same length on both sides.
3. Use the pliers to tighten the screws that hold the string trimmer head in place.

Q: How do I adjust the string on my Hyper Tough Weed Eater?

A: To adjust the string on your Hyper Tough Weed Eater, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string trimmer head.
3. Use the pliers to adjust the tension on the string.
4. Reattach the spark plug wire and turn on the weed eater.

Q: What should I do if my Hyper Tough Weed Eater is not stringing properly?

A: If your Hyper Tough Weed Eater is not stringing properly, there are a few things you can check:

• Make sure that the string is the correct length.
• Make sure that the string is installed correctly.
• Make sure that the string is not tangled.
• Make sure that the string trimmer head is not damaged.

If you have checked all of these things and your Hyper Tough Weed Eater is still not stringing properly, you may need to take it to a service center for repairs.

restringing a Hyper Tough weed eater is a relatively simple task that can be completed in a few minutes. By following the steps outlined in this guide, you can have your weed eater back up and running in no time.

Here are the key takeaways:

• The first step is to remove the old string.
• To do this, you will need to loosen the string tension knob and then pull the old string out of the head.
• Once the old string is removed, you can install the new string.
• To do this, you will need to thread the new string through the eyelets in the head and then tighten the string tension knob.
• Finally, you can test your weed eater to make sure that it is working properly.

By following these steps, you can easily restring your Hyper Tough weed eater and keep your yard looking its best.